A mass balance approach for quantifying the role of natural decay and fate mechanisms on SARS-CoV-2 genetic marker removal during water reclamation.

The recent SARS-CoV-2 outbreak yielded substantial data regarding virus fate and prevalence at water reclamation facilities (WRFs), identifying influential factors as natural decay, adsorption, light, pH, salinity, and antagonistic microorganisms. However, no studies have quantified the impact of these factors in full scale WRFs. Utilizing a mass balance approach, we assessed the impact of natural decay and other fate mechanisms on genetic marker removal during water reclamation, through the use of sludge and wastewater genetic marker loading estimates. Results indicated negligible removal of genetic markers during P/PT (primary effluent (PE) p value: 0.267; preliminary and primary treatment (P/PT) accumulation p value: 0.904; and thickened primary sludge (TPS) p value: 0.076) indicating no contribution of natural decay and other fate mechanisms toward removal in P/PT. Comparably, adsorption and decomposition was found to be the dominant pathway for genetic marker removal (thickened waste activated sludge (TWAS) log loading 9.75 log10 GC/day); however, no estimation of log genetic marker accumulation could be carried out due to high detections in TWAS. PRACTITIONER POINTS: The mass balance approach suggested that the contribution of natural decay and other fate mechanisms to virus removal during wastewater treatment are negligible compared with adsorption and decomposition in P/PT (p value: 0.904). During (P/PT), a higher viral load remained in the (PE) (14.16 log10 GC/day) compared with TPS (13.83 log10 GC/day); however, no statistical difference was observed (p value: 0.280) indicting that adsorption/decomposition most probably did not occur. In secondary treatment (ST), viral genetic markers in TWAS were consistently detected (13.41 log10 GC/day) compared with secondary effluent (SE), indicating that longer HRT and the potential presence of extracellular polymeric substance-containing enriched biomass enabled adsorption/decomposition. Estimations of total solids and volatile solids for TPS and TWAS indicated that adsorption affinity was different between solids sampling locations (p value: <0.0001).

Study on the effect and regularity of plating parts cleaning wastewater by enhanced aerobic process with high-density bacterial flora.

In this research, we established an enhanced aerobic biological method utilizing a high-density bacterial flora for the treatment of low-biochemical plating parts washing wastewater. The elucidation of pollutant removal mechanisms was achieved through a comprehensive analysis of changes in sludge characteristics and bacterial community structure. The results demonstrated that throughout the operational period, the organic load remained stable within the range of 0.01-0.02 kgCOD/kgMLSS·d, the BOD5/COD ratio increased from 0.004 mg/L to 0.33 mg/L, and the average removal rates for key pollutants, including COD, NH4+-N, and TN, reached 98.13%, 99.86%, and 98.09%. MLSS concentration remained at 7627 mg/L, indicating a high-density flora. Notably, Proteobacteria, Bacteroidota, and Acidobacteriota, which have the ability to degrade large organic molecules, had been found in the system. This study affirms the efficacy of the intensive aerobic biological method for treating low-biochemical plating washing wastewater while ensuring system stability.

Sustained oxidation of Tea-Fe(III)/H2O2 simultaneously achieves sludge reduction and carbamazepine removal: The crucial role of EPS regulation.

Establishing an economic and sustained Fenton oxidation system to enhance sludge dewaterability and carbamazepine (CBZ) removal rate is a crucial path to simultaneously achieve sludge reduction and harmless. Leveraging the principles akin to "tea making", we harnessed tea waste to continually release tea polyphenols (TP), thus effectively maintaining high level of oxidation efficiency through the sustained Fenton reaction. The results illustrated that the incorporation of tea waste yielded more favorable outcomes in terms of water content reduction and CBZ removal compared to direct TP addition within the Fe(III)/hydrogen peroxide (H2O2) system. Concomitantly, this process mainly generated hydroxyl radical (•OH) via three oxidation pathways, effectively altering the properties of extracellular polymeric substances (EPS) and promoting the degradation of CBZ from the sludge mixture. The interval addition of Fe(III) and H2O2 heightened extracellular oxidation efficacy, promoting the desorption and removal of CBZ. The degradation of EPS prompted the transformation of bound water to free water, while the formation of larger channels drove the discharge of water. This work achieved the concept of treating waste with waste through using tea waste to treat sludge, meanwhile, can provide ideas for subsequent sludge harmless disposal.

[Effect of Thermal Hydrolysis Pretreatment Time on Microbial Community Structure in Sludge Anaerobic Digestion System].

To evaluate the effect of thermal hydrolysis pretreatment time on the sludge anaerobic digestion system of wastewater treatment plants (WWTPs) in Daxing district, Beijing, the structure and diversity of microbial communities in primary sludge and an activated sludge anaerobic digestion system with different thermal hydrolysis pretreatment times (15 min, 30 min, and 45 min) were analyzed using Illumina MiSeq high-throughput sequencing. The results showed that the dominant groups of digested sludge were mainly distributed in Firmicutes, Cloacimonadota, Chloroflexi, and Synergistota, with W5 being the most common genus. The sum of relative abundance of the dominant phylum was greater than 60%, and W5 accounted for 20.8%-54.5%, showing a high abundance of a few dominant species. During the anaerobic digestion of thermo-hydrolyzed sludge, the relative abundance of acetogenic methanogens decreased due to high levels of volatile fatty acids (VFAs) and ammonia nitrogen (NH4+-N) concentrations, which suggested that the hydrogenophilic methanogenic pathway was more than that of the acetogenic methanogenic pathway. Correlation analysis showed that the soluble protein and pH of thermo-hydrolyzed sludge, NH4+-N of digested sludge, and thermal hydrolysis pretreatment time were the four main environmental factors affecting microbial community structure, and NH4+-N of digested sludge had the largest negative correlation with methanogens. The thermal hydrolysis pretreatment time was negatively correlated with both the Chao index and Shannon index, so longer thermal hydrolysis pretreatment time was not conducive to microbial flora during anaerobic digestion.

[Effects of Vermicomposting on Compost Quality and Heavy Metals：A Meta-analysis].

In order to comprehensively evaluate the effects of vermicomposting on compost quality and the conversion of heavy metals under different control conditions, 109 studies were reviewed. The effects of earthworm species, pre-compost time, ventilation methods, initial C/N, initial pH, and initial moisture of the raw materials on compost quality and the heavy metal toxicity were quantitatively discussed during the vermicomposting process through Meta-analysis. The results showed that the six subgroups of factors all showed obvious influences on the compost quality and heavy metal toxicity. After vermicomposting, the contents of NO3--N (116.2%), TN (29.1%), TP (31.2%), and TK (15.0%) were significantly increased, whereas NH4+-N (-14.8%) and C/N (-36.3%) were significantly decreased. Meanwhile, the total amount of Cu and Cr of the final compost and their bioavailability were significantly reduced. Considering the influences of grouping factors on compost quality and heavy metals, it is recommended to adjust the initial moisture of pile materials to 70%-80%, C/N to 30-85, and pH to 6-7 and to conduct pre-composting for 0-15 d; additionally, vermicomposting should be naturally placed when the composting is aimed at promoting the compost quality. If the main purpose is to weaken the perniciousness of heavy metals in the raw material, it is recommended to adjust the initial moisture of the material to 50%-60%, C/N to less than 30, and pH to 7-8; to conduct no pre-compost; regularly turn the piles; and use the earthworm Eudrilus eugeniae for vermicomposting.

Non-filamentous bulking of activated sludge induced by graphene oxide: Insights from extracellular polymeric substances.

Widespread use of nanomaterials raises concerns. The underlying mechanism by which graphene oxide (GO) nanoparticles causes poor settleability of activated sludge remains unclear. To explore this mechanism, three reactors with different GO concentrations were established. Extended Derjaguin-Landau-Verwey-Overbeek theory indicated that GO destroyed the property of extracellular polymeric substances (EPS), increasing the energy barrier between bacteria. Low levels of uronic acid and hydrogen bonding in exopolysaccharide weakened the EPS gelation increasing aggregation repulsion. Lager amounts of hydrophilic amino acid and looser structure of extracellular proteins for exposing inner hydrophilic groups significantly contributed to the hydrophilicity of EPS. Both changes implied deterioration in EPS structure under GO stress. Metagenome demonstrated a decrease in genes responsible for capsular polysaccharide colonization and genes regulated the translocation of loose proteins were increased, which increased repulsion between bacteria. This study elucidated that changes in EPS secretion under GO exposure are the underlying causes of poor settleability.

Effect of hydrothermal carbonization on pyrolysis behavior, nutrients and metal species distribution in municipal sludge.

In this study, the effect of hydrothermal carbonation (HTC) on the pyrolysis behavior and the distribution of nutrients and metal species of waste-activated sludge (WAS) was investigated. Results showed that the pyrolysis activation energy range of WAS decreased from 11 to 57 kJ/mol to 10-36 kJ/mol when the hydrothermal carbonization was at 160 °C. As indicated by thermodynamic parameters, the hydrothermal carbonization process reduces the pyrolysis reaction activity of the hydrochar. The results of the chemical analysis indicate that hydrothermal carbonization significantly enhances the release of phosphorus and nitrogen, with maximum recovery at a temperature of 200 °C. The standard measurement and testing protocol revealed that hydrothermal carbonization increased the content of non-apatite inorganic P fraction in hydrochar and enhanced the availability of P. Heavy metal analysis shows that hydrothermal carbonization can strengthen the stability of heavy metals in WAS.

Accounting for the microbial assembly of each process in wastewater treatment plants (WWTPs): study of four WWTPs receiving similar influent streams.

We evaluated a unique model in which four full-scale wastewater treatment plants (WWTPs) with the same treatment schematic and fed with similar influent wastewater were tracked over an 8-month period to determine whether the community assembly would differ in the activated sludge (AS) and sand filtration (SF) stages. For each WWTP, AS and SF achieved an average of 1-log10 (90%) and <0.02-log10 (5%) reduction of total cells, respectively. Despite the removal of cells, both AS and SF had a higher alpha and beta diversity compared to the influent microbial community. Using the Sloan neutral model, it was observed that AS and SF were individually dominated by different assembly processes. Specifically, microorganisms from influent to AS were predominantly determined by the selective niche process for all WWTPs, while the microbial community in the SF was relatively favored by a stochastic, random migration process, except two WWTPs. AS also contributed more to the final effluent microbial community compared with the SF. Given that each WWTP operates the AS independently and that there is a niche selection process driven mainly by the chemical oxygen demand concentration, operational taxonomic units unique to each of the WWTPs were also identified. The findings from this study indicate that each WWTP has its distinct microbial signature and could be used for source-tracking purposes.IMPORTANCEThis study provided a novel concept that microorganisms follow a niche assembly in the activated sludge (AS) tank and that the AS contributed more than the sand filtration process toward the final microbial signature that is unique to each treatment plant. This observation highlights the importance of understanding the microbial community selected by the AS stage, which could contribute toward source-tracking the effluent from different wastewater treatment plants.

Mechanistic insight into the aggregation ability of anammox microorganisms: Roles of polarity, composition and molecular structure of extracellular polymeric substances.

The chemical characteristics of extracellular polymeric substances (EPS) of anammox bacteria (AnAOB) play a crucial role in the rapid enrichment of AnAOB and the stable operation of wastewater anammox processes. To clarify the influential mechanisms of sludge EPS on AnAOB aggregation, multiple parameters, including the polarity distribution, composition, and molecular structure of EPS, were selected, and their quantitative relationship with AnAOB aggregation was analyzed. Compared to typical anaerobic sludge (anaerobic floc and granular sludge), the anammox sludge EPS exhibited higher levels of tryptophan-like substances (44.82-56.52 % vs. 2.57-39.81 %), polysaccharides (40.02-53.49 mg/g VSS vs. 30.22-41.69 mg/g VSS), and protein structural units including α-helices (20.70-23.98 % vs. 16.48-19.32 %), ß-sheets (37.43-42.98 % vs. 25.78-36.72 %), and protonated nitrogen (Npr) (0.065-0.122 vs. 0.017-0.061). In contrast, it had lower contents of ß-turns (20.95-27.39 % vs. 28.17-39.04 %). These biopolymers were found to originate from different genera of AnAOB. Specifically, the α-helix-rich proteins were mainly derived from Candidatus Kuenenia, whereas the extracellular proteins related to tryptophan and Npr were closely associated with Candidatus Brocadia. Critically, these EPS components could drive anammox aggregation through interactions. Substantial amounts of tryptophan-like substances facilitated the formation of ß-sheet structures and the exposure of internal hydrophobic clusters, which benefited the anammox aggregation. Meanwhile, extracellular proteins with high Npr content played a pivotal role in the formation of mixed protein-polysaccharide gel networks with the electronegative regions of polysaccharides, which could be regarded as the key component in the maintenance of anammox sludge stability. These findings provide a comprehensive understanding of the multifaceted roles of EPS in driving anammox aggregation and offer valuable insights into the development of EPS regulation strategies aimed at optimizing the anammox process.

Comparative investigations on the incorporation of biogenic Fe products into anaerobic granular sludge of different sources: Fe loading capacity, physicochemical properties, microbial community and long-term methanogenesis performance.

Anaerobic granular sludge (AGS) has been regarded as the core of lots of advanced anaerobic reactors. Formation of biogenic Fe products and their incorporation into AGS could influence interspecies electron transfer and methanogenesis performance. In this study, with anaerobic granular sludge (AGS) from different sources (brewery, chemical plant, paper mill, citric acid factory, and food factory) as the research targets, the formation of biogenic iron products in AGS through the biologically induced mineralization process was studied. Furthermore, the influences of physicochemical properties and microbial community on methanogenesis were investigated. Results showed that all the AGS of different sources possessed the capacity to form biogenic Fe products through dissimilatory iron-reduction process, and diverse Fe minerals including magnetite (Fe3O4), hematite (Fe2O3), goethite (FeOOH), siderite (FeCO3) and wustite (FeO) were incorporated into AGS. The AGS loaded with Fe minerals (Fe-AGS) showed increased conductivity, magnetism and zeta-potential comparing to the control. Those Fe-AGS of different sources demonstrated different methanogenesis performance during the long-term operation (50 days). Methane production was increased for the Fe-AGS of citric acid (6.99-32.50%), food (8.33-37.46%), chemical (2.81-7.22%) and brewery plants (2.27-2.81%), but decreased for the Fe-AGS of paper mill (54.81-72.2%). The changes of microbial community and microbial correlations in AGS as a response to Fe minerals incorporation were investigated. For the Fe-AGS samples with enhanced methane production capability, it was widely to find the enriched populations of fermentative and dissimilatory iron reducing bacteria Clostridium_sensu_stricto_6, Bacteroidetes_vadinHA17 and acetoclastic methanogens Methanosaeta, and positive correlations between them. This study provides comprehensive understanding on the effects of incorporation biogenic Fe products on AGS from different sources.

Assessment of the microbial electrochemical sensor (SENTRY™) as a potential wastewater quality monitoring tool for common pollutants found in Malaysia.

Bioelectrochemical sensors for environment monitoring have the potential to provide facility operators with real-time data, allowing for better and more timely decision-making regarding water and wastewater treatment. To assess the robustness and sensitivity of the Sentry™ biosensor in local conditions, it was tested in Malaysia using domestically available wastewater. The study objectives included (1) enrich the biosensor locally, (2) operate and test the biosensor with local domestic wastewater, and (3) determine the biosensor's responsiveness to model pollutants through pollutant spike and immersion test as well as response to absence of wastewater. Lab-scale operation shows the biosensor was successfully enriched with (1) local University Kebangsaan Malaysia's, microbial community strain collection and (2) local municipal wastewater microflora, operated for more than 50 days with a stable yet responsive carbon consumption rate (CCR) signal. Meanwhile, two independent biosensors were also enriched and operated in Indah Water Research Centre's crude sewage holding tank, showing a stable response to the wastewater. Next, a pilot scale setup was constructed to test the enriched biosensors for the spiked-pollutant test. The biosensors showed a proportional CCR response (pollutant presence detected) towards several organic compounds in the sewage, including ethanol, chicken blood, and dilution of tested sewage but less to curry powder, methanol, and isopropanol. Conversely, there was no significant response (pollutant presence not detected) towards hexane, Congo red, engine oil, and paint, which may be due to their non-biodegradability and/or insoluble nature. Additionally, the biosensors were exposed to air for 6 h to assess their robustness towards aerobic shock with a positive result. Overall, the study suggested that the biosensor could be a powerful monitoring tool, given its responsiveness towards organic compounds in sewage under normal conditions.

Enhancement of methane production from anaerobic digestion of Erigeron canadensis via O2-nanobubble water supplementation.

Malignant invasive Erigeron canadensis, as a typical lignocellulosic biomass, is a formidable challenge for sustainable and efficient resource utilization, however nanobubble water (NBW) coupled with anaerobic digestion furnishes a prospective strategy with superior environmental and economic effectiveness. In this study, influence mechanism of various O2-NBW addition times on methanogenic performance of E. canadensis during anaerobic digestion were performed to achieve the optimal pollution-free energy conversion. Results showed that supplementation of O2-NBW in digestion system could significantly enhance the methane production by 10.70-16.17%, while the maximum cumulative methane production reached 343.18 mL g-1 VS in the case of one-time O2-NBW addition on day 0. Furthermore, addition of O2-NBW was conducive to an increase of 2-90% in the activities of dehydrogenase, α-glucosidase and coenzyme F420. Simultaneously, both facultative bacteria and methanogenic archaea were enriched as well, further indicating that O2-NBW might be responsible for facilitating hydrolytic acidification and methanogenesis. Based on Kyoto Encyclopedia of Genes and Genomes (KEGG) cluster analysis, provision of O2-NBW enhanced the metabolism of carbohydrate and amino acid, translation as well as membrane transport of bacteria and archaea. This study might offer the theoretical guidance and novel insights for efficient recovery of energy from lignocellulosic biomass on account of O2-NBW adhibition in anaerobic digestion system, progressing tenor of carbon-neutral vision.

Enhanced aerobic granular sludge with micro-electric field for sulfamethoxazole degradation: Efficiency, mechanism, and microbial community.

In this study, an aerobic granular sludge electrochemical system (AGES) was established by applying the micro-electric field to an aerobic granular sludge (AGS) reactor for the degradation of sulfamethoxazole (SMZ). Under the stimulation of the micro-electric field, the granulation of sludge was improved and the degradation rate of SMZ was enhanced. The features of granular sludge were characterized by scanning electron microscopy and X-ray diffraction. The optimal degradation rate of SMZ (88%) was obtained at the voltage of 3 V and the effective electrode area of 800 mm2. The results of kinetics analyses revealed that the degradation of SMZ by AGES can be fitted with the second-order kinetic equation, showing a degradation rate constant (k) of 0.001 L mol-1·min-1. The degradation products of SMZ in the AGES system were detected by LC-MS and their possible degradation routes were elucidated. The micro-electric field in the AGES system played a selective role in microbes' enrichment and growth, changing the diversity of the microbial community. Pseudomonas, Tolumonas, and Acidovorax were the dominant bacteria in the AGES system, which is accountable for the abatement of SMZ and nutrients. This work provides a green means for improving AGS and paves the way for applying the AGS process to real-world wastewater treatment.

Treatment of aqueous phase from hydrothermal liquefaction of municipal sludge by adsorption: Comparison of biochar, hydrochar, and granular activated carbon.

Hydrothermal liquefaction (HTL) is promising for treating waste with high moisture, such as municipal sludge, and producing biocrude (a petroleum-like biofuel). However, a large amount of wastewater byproduct, HTL aqueous, is generated. The presence of hazardous compounds (e.g., phenolic compounds and nitrogenous organics) makes HTL aqueous the biggest bottleneck for full-scale implementation at treatment plants. This study investigated the adsorption of various pollutants, focusing on chemical oxygen demand (COD), in HTL aqueous to granular activated carbon (GAC), biochar, and hydrochar. It assessed the effect of pH, temperature, time, and adsorbent concentration on adsorption efficiency and identified proper adsorbent and process conditions for removing most of the pollutants from HTL aqueous. GAC showed the highest adsorption capacity (184 mg/g) for COD, surpassing biochar (44 mg/g) and hydrochar (42 mg/g). The adsorption of COD to all adsorbents followed pseudo-second-order kinetic and Freundlich isotherm, suggesting that the adsorption of HTL aqueous pollutants is a heterogeneous and multilayer process, limited by chemosorption. The adsorption was endothermic, favored by elevated temperatures and neutral pH. This means adsorption is more efficient and economical for treating HTL aqueous that is a hot stream at the large-scale and it saves chemical needs. Lastly, GAC was highly efficient and selective in removing harmful pollutants, such as COD (up to 66%), total phenolic compounds (up to 94%), pyrazines (up to 99%), pyridines (up to 100%), and cyclic ketones (up to 95%) while preserving valuable volatile fatty acids (VFAs) and ammonia for subsequent recovery. Removal of potentially inhibitory compounds and preserving VFAs are crucial for carbon recovery in anaerobic biological treatment of HTL aqueous. The results suggested the necessity of optimizing adsorbent dose for maximizing removal of specific group of inhibitory compounds in full-strength HTL aqueous for enhancing downstream biological treatment. Lastly, this study established the groundwork for HTL aqueous adsorption, elucidating its effectiveness and mechanism for pollutant removal.

Deep eutectic solvents pretreatment enhances methane production from anaerobic digestion of waste activated sludge: Effectiveness evaluation and mechanism elucidation.

Anaerobic digestion (AD) is a prevalent waste activated sludge (WAS) treatment, and optimizing methane production is a core focus of AD. Two DESs were developed in this study and significantly increased methane production, including choline chloride-urea (ChCl-Urea) 390% and chloride-ethylene glycol (ChCl-EG) 540%. Results showed that ChCl-Urea mainly disrupted extracellular polymeric substances (EPS) structures, aiding in initial sludge solubilization during pretreatment. ChCl-EG, instead, induced sludge self-driven organic solubilization and enhanced hydrolysis and acidification processes during AD process. Based on the extent to which the two DESs promoted AD for methane production, the AD process can be divided into stage Ⅰ and stage Ⅱ. In stage Ⅰ, ChCl-EG promoted methanogenesis more significantly, microbiological analysis showed both DESs enriched aceticlastic methanogens-Methanosarcina. Notably, ChCl-Urea particularly influenced polysaccharide-related metabolism, whereas ChCl-EG targeted protein-related metabolism. In stage Ⅱ, ChCl-Urea was more dominant than ChCl-EG, ChCl-Urea bolstered metabolism and ChCl-EG promoted genetic information processing in this stage. In essence, this study investigated the microbial mechanism of DES-enhanced sludge methanogenesis and provided a reference for future research.

Aerobic digestibility of waste aerobic granular sludge (AGS) assessed by respirometry, physical-chemical analyses, modeling and 16S rRNA gene sequencing.

Research has evolved on aerobic granular sludge (AGS) process, but still there are very few studies on the treatment of excess AGS sludge, with almost none considering its aerobic digestion. Here therefore, the aerobic digestibility of typical AGS sludge was assessed. Granules were produced from acetate-based synthetic wastewater (WW) and were subjected to aerobic digestion for 64 d. The stabilization process was monitored over time through physical-chemical parameters, oxygen uptake rates (OUR) and 16S rRNA gene sequencing. The microbial analyses revealed that the cultivated granules were dominated by slow-growing bacteria, mainly ordinary heterotrophic organisms with potential for polyhydroxyalkanoates (PHA) aerobic storage (PHA-OHOs), polyphosphate and glycogen accumulating organisms (PAOs and GAOs), fermentative anaerobes and nitrifiers (AOB and NOB). Differential abundance analysis of the bacterial data (before versus after digestion) discriminated between the most vulnerable microbiome genera and those most resistant to aerobic digestion. Furthermore, modeling of the stabilization process determined that the endogenous decay rate constant (bH) for the heterotrophs present in the granules was notably low; bH = 0.05 d-1 (average), four times less than for common activated sludge (AS), which is rated at 0.2 d-1. For first time, the research reveals another important feature of AGS sludge, i.e. the slow-decaying character of its bacteria (along with their known slow-growing character). This results in slower stabilization, need of bigger digesters and reconsideration of the specific OUR limits in biosolids regulations (SOUR limit of 1.5 mg/gTSS.h), for waste AGS compared to conventional waste AS. The study suggests that aerobic digestion of waste AGS (fully-granulated) could differ from that of conventional AS. Future work is needed on aerobic digestibility of real AGS sludges from municipal and industrial WWs, compared to synthetic WWs.

Vital role of CYP450 in the biodegradation of antidiabetic drugs in the aerobic activated sludge system and the mechanisms.

The extensive use of antidiabetic drugs (ADDs) and their detection in high concentrations in the environment have been extensively documented. However, the mechanism of ADDs dissipation in aquatic environments is still not well understood. This study thoroughly investigates the dissipation behavior of ADDs and the underlying mechanisms in the aerobic activated sludge system. The results indicate that the removal efficiencies of ADDs range from 3.98% to 100% within 48 h, largely due to the biodegradation process. Additionally, the gene expression of cytochrome P450 (CYP450) is shown to be significantly upregulated in most ADDs-polluted samples (P < 0.05), indicating the vital role of CYP450 enzymes in the biodegradation of ADDs. Enzyme inhibition experiments validated this hypothesis. Moreover, molecular docking and simulation results indicate that a strong correlation between the biodegradation of ADDs and the interactions between ADDs and CYP450 (Ebinding). The differences in dissipation behavior among the tested ADDs are possibly due to their electrophilic characteristics. Overall, this study makes the initial contribution to a more profound comprehension of the crucial function of CYP450 enzymes in the dissipation behavior of ADDs in a typical aquatic environment.

Effects of yeast inoculation methods on caproic acid production and microbial community during anaerobic fermentation of Chinese cabbage waste.

To provide a sufficient supply of electron donors for the synthesis of caproic acid, yeast fermentation was employed to increase ethanol production in the anaerobic fermentation of Chinese cabbage waste (CCW). The results showed that the caproic acid yield of CCW with ethanol pre-fermentation was 7750.3 mg COD/L, accounting for 50.2% of the total volatile fatty acids (TVFAs), which was 32.5% higher than that of the CCW without yeast inoculation. The synchronous fermentation of yeast and seed sludge significantly promoted the growth of butyric acid consuming bacterium Bacteroides, resulting in low yields of butyric acid and caproic acid. With yeast inoculation, substrate competition for the efficient ethanol conversion in the early stage of acidogenic fermentation inhibited the hydrolysis and acidfication. Without yeast inoculation, the rapid accumulation of TVFAs severely inhibited the growth of Bacteroidetes. In the reactor with ethanol pre-fermentation, the key microorganism for caproic acid production, Clostridium_sensu_stricto_12, was selectively enriched.

Study on mechanism of removal of sudden Tetracycline by compound modified biological sand filtration process.

The removal of tetracycline from the sewage plant effluents through advanced treatment methods is key to controlling tetracycline levels in the water environment. In this study, modified quartz sands (QS) were used in a biological sand filter to remove tetracycline. The modified QS, with different surface characteristics, were prepared using glass etching technology combined with subsequent chemical modification methods, including hydroxylation treatment, metal ion modification, and amino modification. The adsorption efficiency of hydroxylated QS was higher than that of metal ion modified and amino modified QS, with adsorption efficiencies of 20.4331 mg/kg, 12.8736 mg/kg, and 10.1737 mg/kg, respectively. Results indicated that QS primarily reduce tetracycline through adsorption. Adsorption on ordinary QS fit the pseudo-first-order kinetic model, while adsorption on other modified QS and biofilm-coated QS fit the pseudo-second-order kinetics model. Biodegradation was identified as another mechanism for tetracycline reduction, which fit the zero-order kinetic model. Pseudomonas alcaligenes and unclassified Pseudomonas accounted for 96.6% of the total tetracycline-degrading bacteria. This study elucidates the effectiveness and mechanisms of five types of QS in treating tetracycline from sewage plant effluents. It provides a novel method for tetracycline reduction in real-world wastewater scenarios.

Stabilization of heavy metals in solid waste and sludge pyrolysis by intercalation-exfoliation modified vermiculite.

Increasing amounts of solid waste and sludge have created many environmental management problems. Pyrolysis can effectively reduce the volume of solid waste and sludge, but there is still the problem of heavy metal contamination, which limits the application of pyrolysis in environmental management. The intercalated-exfoliated modified vermiculite (IEMV) by intercalators of sodium dodecylbenzene sulfonate, hexadecyltrimethylammonium bromide and octadecyltrimethylammonium bromide were used to control the release of Cd, Cr, Cu, Zn and Pb during pyrolysis process of sludge or solid waste. The retention of heavy metals in sludge was generally better than that in solid waste. The IEMV by octadecyltrimethylammonium bromide as the intercalator calcined 800 °C (STAB-800) was the best additive for heavy metal retention, and the retention of Cr, Cu and Zn was significantly better than that of Pb and Cd. Cr, Cu, Zn and Pb were at low risk, while Cd had considerable risk under certain circumstances. New models were proposed to comprehensively evaluate the results of the risk and forms of heavy metals, and the increasing temperature was beneficial in reducing the hazards of heavy metals by the addition of STAB-800. The reaction mechanism of heavy metals with vermiculite was revealed by simulation of reaction sites, Fukui Function and Frontier Molecular Orbital. Thermal activation-intercalated-exfoliated modified vermiculite (T-IEMV) is more reactive and had more active sites for heavy metals. Mg atoms and outermost O atoms are the main atoms for T-IEMV to react with heavy metals. The Cr, Cu and Zn have better adsorption capacity by T-IEMV than Pb and Cd. This study provides a new insight into managing solid waste and sludge and controlling heavy metal environmental pollution.